Put front and back on top of each other with _good sides together_.
Sew the side seams and the short seams at the shoulder straps. If you have a serger, this is a good moment to use it. If not, finish your seams otherwise.
## Step 2: Finish hem
Fold the hem upwards, and sew it down. If you have a coverlock, use it. If not, use a _twin needle_ or _zig-zag stitch_ to keep the seam stretchable.
If you are new to [knit binding](/docs/sewing/knit-binding), you might read [this page on the subject](/docs/sewing/knit-binding).
###### Repeat steps 3 and 4 for both armholes and the neck opening
The procedure outlined below applies to both of the armholes as well as the neck opening. In other words, you'll have to do this three times.
###### Start with the simplest opening
I would advise you to start with whatever opening has the most uniform curvature. By default, those are the arm holes, but if you changed the pattern options (think racerback) that might not be the case.
Either way, the less sharp bends you have, the easier it will be. So start with that to warm up before you do the trickier bends.
This is the only part of making this A-shirt that requires a bit of practice. Don't worry, all you need to do is make a couple of these and you'll be a pro in no time.
The first thing we need to do is decide where we are going to start/stop our binding. Here's what I suggest:
- For the armholes: at the side seam. This will hide our seam under the arm
- For the neck opening: the center back of the neck. You might want to mark this with a pin
### Place (the start of) your binding
Put your A-shirt down with the good side up, and place your binding strip on top of it with the good side down (as in, good sides together).
Align the long edge of your strip with the edge of your fabric so the strip lies on top of the fabric (not in the opening). Place the corner on your starting point.
Now shift your binding strip 1cm beyond your starting point. This little extra will guarantee we can join the two ends later.
### Make sure you know where to sew
We are going to sew 1.5cm from the edge. So be careful because this is not the standard seam allowance.
Also, we are not starting at our start point, but we skip the first 3cm. We'll need this wiggle room later to join the ends of our binding.
### Sew binding in place
Sew your binding in place while gently stretching the binding, but not the fabric. Make sure not to sew the last 3cm but leave them, just as you did at the start.
You might need to practice a bit to get the hang of it.
> Make sure to stretch your binding more when you're taking a sharper bend.
> Read my notes on [knit binding](/docs/sewing/knit-binding) for more info.
### Mark binding ends
With about 6cm left to go before we complete our circle, it's time to sew the ends of the binding together.
Take one of the edges, and stretch it along the 3cm separating it from the start point as you would while sewing.
Mark the binding where it reaches the start point. Do the same for the other end.
### Sew binding ends together
Fold your A-shirt in whatever way makes it easier for you to place both binding ends with good sides together, aligning the marks. Sew them together on the mark.
> 6 cm is not much, but should be enough to get both edges comfortably under your sewing machine to sew them together.
### Finish last 6cm of binding
Now that your binding ends are joined together, it's time to finish the last 6cm of binding. Sew it down, staying 1.5cm from the edge as you did before.
## Step 4: Fold knit binding to the back and sew down
### Fold your binding over the fabric edge to the back
Fold your binding fabric around the fabric of your A-shirt to the back. This is how we'll sew it down.
> While the fabric is folded double at the front (hiding the fabric edge in the process) there's no need for that at the back. We will merely trim back the edge later, given that knit doesn't ravel. If we were to fold back the fabric at the back too, it would only add bulk.
### Sew your binding down
From the right side of your fabric, sew along the inner edge of your binding (furthest from the edge), making sure to catch the binding at the back in the process.
