freesewing/markdown/org/docs/designs/huey/instructions/fr.md

---
title: "Huey hoodie: Sewing Instructions"
---

<Note>

Ce patron peut être cousu avec ou avec une surjeteuse. If not using a overlocker or serger you will have to _Finish_ the seams.

</Note>

### Step 1: Attaching the pockets

- Press under seam allowance of top, curved and slanted edges.
- _Topstitch_ or _Edgestitch_ the curved seam allowance in place. This will form the openings of the pockets.
- Pin the pockets to the fronts using the guidelines and match raw edges.
- Baste the raw edges of the pockets and fronts together.
- _Topstitch_ or _Edgestitch_ the top and slanted edges of the pockets to the fronts leaving the curved edges open.

### Step 2: Making the Body

- With _good sides together_, sew the Fronts to the backs at the shoulder seams.
- With _good sides together_, sew the sleeves to the front and back matching notches.
- With _good sides together_, sew up the sleeves and side seams.

### Step 3: Making drawstring holes (Optional)

If you don't wish to add a drawstring you can skip to Step 4.

- Take one matching set of the Hood pieces, that you intend to feature on the outside of the finished hoodie.
- Mark the place for a hole on each hood piece, along the inner curve.
  - The hole should be about 1.5-2cm from the edge of the fabric. This is to keep your seam allowance out of the way.
  - The hole should be located slightly up from the bottom of the inner curve. This is to keep it away from the front seams.
- On the wrong side of the fabric, face where you are making the hole to stabilise the fabric.
- Faites une boutonnière à votre marque, soit à la main, soit a la machine.
- Vous pouvez aussi construire ou utiliser des œillets à la marque.

<Tip>

Si vous n'avez pas ou ne souhaitez pas utiliser d'entoilage, vous pouvez utiliser un morceau de tissu robuste tel que le denim.

</Tip>

<Note>

Les cordons seront enfilés après la construction du sweat à capuche.

</Note>

### Etape 4 : Préparation de la capuche

- With _good sides together_, matching sets, sew the hood pieces together along the outer curve edge.
- With _good sides together_, matching seams, sew the inner hood to the outer hood along the inner curve edge.
- Turn good sides out.
- Baste the front and bottom raw edges together.
- Create a casing for the drawstring by stitching about 2.5cm (1 inch) away from the inner edge on the side with the drawstring holes.
- (Optionaly) If not using a drawstring, _Topstitch_ or _Edgestitch_ the inner curve.

<Note>

When creating the casing or topstitching, make sure the inner curve seam is slightly inside of the hood to stop it from peaking out in the future.
Alternatively if not using a drawstring you can _Understitch_ the inner curve seam.

</Note>

### Step 5: Making a neckband (Optional)

A neckband can be useful to stablise and cover the neck seams but it is optional if you wish to skip it.

- Cut a cross-wise strip of fabric out of your main fabric:
  - Your neck opening + double your front seam allowance long
  - Triple your neck seam allowance wide.

### Step 6: Attaching the hood

- Pin the hood to the neck with outer hood matching _good side_ of neck.
- If using, pin the neckband _good side_ to inner hood matching raw edges.
- Sew the neckband seam.
- _Finish_ seam if not using neckband then proceed to Step 7.
- Press neckband down.
- On outside _Topstitch_ neckband in place.
- À l'intérieur, coupez la bande de cou vers le bas pour le surfiler.

### Étape 7 : Attacher la ceinture

- Pliez la ceinture en 2 dans le sens de la longueur envers contre envers. Repasser.
- Avec _bons côtés_ ensemble coudre la ceinture au bas du dos et de l'avant.
- Repassez la couture vers le haut.
- _Topstitch_ or _Edgestitch_ waistband seam allowance to the body.

### Étape 8 : Attacher les poignets

- Avec _bons côtés ensemble,_ coudre cotés courts des poignets pour créer deux bandes.
- Repasser pour ouvrir la marge de couture.
- (Optional) _Edgestitch_ the seam allowances down.
- Pliez les poignets en 2 dans le sens de la longueur envers contre envers. Repasser.
- Matching seams and raw edges, pin the cuffs to the sleeves _good sides together_.
- Sew the cuffs to the sleeves.
- Press the seam allowances up.
- _Topstitch_ or _Edgestitch_ cuffs seam allowances to the sleeves.

### Step 9: The zipper

- If need be, face the front edges of the hoodie.
- Unzip the zipper part way.
- Fold the top of the zipper tape down to the _good side_ of the zipper tape. Trim if need be.
- Pin the zipper along one of the front edges of the hood, front and waistband. The zipper teeth should just be slightly over the seam line with the edge of the tape either matching or being slightly over from the hoodie edge. Making sure the zipper pull is faced the _good sides_ of the hoodie and the bottoms are lined up.
- Using a zipper foot stitch the zipper to the hoodie using you seam allownace width. When you reach the zipper pull, stop, put your needle down, lift the presser foot, pull the zipper pull past the presser foot, lower the presser foot. Then you can continue sewing the seam.
- Unzip the zipper.
- Pin and sew the unattached zipper tape to the other side of the hoodie the same way.
- Press the seams to the inside being careful not to melt the zipper teeth with your iron.
- _Topstitch_ the zipper tapes in place. You may need to use a zipper foot.

<Tip>

To help match the pockets and seams, when it is attached to one side and temporarily mark the corresponding teeth at the pockets and seam. You can now use these marks to align the zipper to the pocket and seams on the other side.

</Tip>

<Note>

You only need to face your fabric if it is very stretchy or needs a bit more stability.

</Note>

### Step 10: Thread the drawstring

- Thread the drawing string through the drawstring holes.
- If needed secure the ends of the drawstring e.g. with something like aglets.

<Tip>

Use a safety pin to help thread the drawstring.

</Tip>

### Étape 11: Profitez-en!

- Voilà! Vous avez terminé ! Now go feel warm and comfy in your new hoodie!

<Note>

Ce patron a été mis en vedette dans le [numéro 27 du magazine HackSpace ](https://hackspace.raspberrypi.org/issues/27),
l'article contient également des instructions, donc vous pouvez vouloir le consulter.

</Note>