New translations en.md (Dutch)

markdown/org/docs/patterns/titan/instructions/nl.md

@@ -1,29 +1,70 @@
+<Note>
 
-### Stap 1: Bevestig de buitennaad
+###### Titan is a block, not a pattern
 
-Stik de buitennaad aan (de naad die langs de zijkant van je been loopt) van het voor- en achterpand.
+A block is a basic shape on which other patterns are based.
+They are sometimes also called slopers, although purists will argue that a block and a sloper are different things.
 
-Herhaal de stap voor de andere broekspijp, maar **zorg ervoor dat ze de spiegelafbeelding van elkaar** zijn.
+Blocks are typically not made as-is but rather serve as a basis for other patterns so the instructions below will not go in depth about closures or finishes and are for the default Titan block.
 
-### Stap 2: Bevestig de binnennaad
+</Note>
 
-Bevestig de binnennaad (de naad die langs de binnenkant van je broekspijp) van de voor- en achterpand.
+### Step 1: Mock-up Construction
 
-Je hebt nu een been. Herhaal deze stap voor de andere benen, waarbij ze er nogmaals voor zorgen dat ze spiegelbeelden van elkaar zijn.
-
-### Stap 3: Bevestig de kruisnaad
-
-Keer de ene broekspijp met de goede kant in, en de andere met de goede kant naar buiten.
-
-Grijp nu de *goede kant uit* in de *goede kant in* broekspijp, zodat ze hun _goede kanten samen_ hebben.
-
-Je kan nu de kruisnaad uitlijnen en stikken.
+- Join the outseam (the seam that runs along the side of your leg) of the front and back.
+- Join the inseam (the seam the runs along the inside of your legs) of the front and back.
+- You now have a leg. Repeat for the other leg, **making certain they are mirror images of each other**.
+- Turn one leg with the good side in, and the other with the good side out.
+- Now tuck the *good side out* into the *good side in* leg, so that they have their _good sides together_.
+- Align and sew the cross seam.
 
 <Note>
 
-###### Je wilt waarschijnlijk een rits
-
-plaatsen of het laatste deel van de kruisnaad laten open (zodat je hem kan spelen).  
-Als je niet in staat bent Titan op de juiste plek te zetten.
+You may need to leave an opening in the front cross seam so you can pin yourself in.
+
+</Note>
+
+<Tip>
+
+If you are making adjustments you may wish to sew the seams wrong sides together to make them easier to adjust.
+
+</Tip>
+
+### Step 2: Try it on
+
+- Try it on and check the fit by pinning the front closed whilst wearing it.
+- Make any alterations and try it on again.
+- Repeat until you are happy.
+
+<Tip>
+
+Keep an eye out for anything you keep doing whilst wearing the mock-up, are you pulling it down? Constantly adjusting the shoulder? etc. Things like these are signs of where the pattern may need adjusting.  
+
+Sometimes you may need to wear the mock-up for an extended amount of time to get a better sense of the fit so don't be afraid to walk around in it for a couple of hours.
+
+</Tip>
+
+<Note>
+  
+Remember to treat Titan as a basis rather than a final product, so adjust what you need to get the desired look.  
+For instance:
+- Add a front closure
+- Add pockets
+- Change the pant length
+- Change the pant width
+- Add a waistband
+
+It is all up to you! Experiment and go forth!
+
+</Note>
+
+### Step 3: Make a paper pattern
+
+- Once happy with all your changes unpick your mockup and make a paper pattern based off of it.
+- Now you have a pattern you can use to produce a garment.
+
+<Note>
+
+It is best practice to make a paper pattern from the mock-up if you have made any alterations, as this will allow you to clean up any lines but also means you have a pattern that you can keep producing garments from.
 
 </Note>